Through hole taper shaft encoder 9mm shaft KN40 encoder 2500ppr 6
poles 5VDC
Matters needing attention
1. Must choose the power supply voltage: DC5V or DC8-30V
2. Must choose leaf spring plate model number if you select hollow
shaft encoder
3. Please advise the motor speed (RPM) that you actually use
4. If you have any other requirements, please provide detail
parameters
KN40 encoder Specification
| Brand | HENGXIANG |
| Encoder type | Incremental encoder |
| External diameter | 40mm |
| Thickness | 20mm |
| Installation dimension | R17mm, R20mm;R23mm |
| Hollow shaft type | blind hole; through hole, taper hole,solid taper shaft |
| Solid shaft diameter | 10mm (taper shape) |
| Hollow shaft diameter | 6mm;8mm;9mm;9.52mm;10mm |
| Resolution | 1024;2048;2500;3600;5000;7200;10000;14400 |
| 1000/4;1000/6;1000/8;1024/4;1024/6；1024/8；2000/4；2000/6；2000/8；2048/4；2048/6;2048/8；2500/4；2500/6；2500/8;4096/4;4096/6;4096/8;5000/4;5000/6;5000/8 |
| Output phase | Phase A+,B+,Z+,A-,B-,Z-,U+,V+,W+,U-,V-,W- |
| Supply voltage | DC5V ; DC8--30V |
| Outlet type | Cable out from side |
| Output mode | NPN/PNP(Open Collector Output) |
| Voltage output |
| Push-pull output |
| line drive (26LS31) TTL |
| line drive(DC8-30V) HTL |
| TTL(DC5V) phase ABZ are back of phase UVW |
| Protection grade | IP40 |
| Cable length | 500mm |
| Consumption current | 100mA MAX |
| Top response frequency | 300KHZ |
| Allowable ripple | ≤3%rms |
| Load Voltage | ≤DC30V |
| Insulation strength | AC500V 60s |
| Insulation resistance | 10MΩ |
| GND | not connect to encoder |
| Mark to Space ratio | 45% to 55% |
| starting torque | less than 5.9x 10-3 N.m |
| Intertia moment | less than 1.5x 10-6kg.m2 |
| Shaft load | Radial 30N; Axial 20N |
Factory Encoder Production Capability
5000 pieces per month
-------- Production Line Capacity
50000 pieces per year
--------Actual Units Produced (Previous Year)
Some part number of KN40 series encoder
KN40-J2V5000B6
KN40-J3F4096B8
KN40-J4C1024B9.52
KN40-J6E2048B10
KN40-J12C2500/8Q6
KN40-J2F20000Q8
KN40-J3N16384Q10
KN40-J12C4096/Q84
KN40-J6E2048Q10
KN40-J4C1024Z9
Signal Circuit of encoder
1. The NPN Open Collector -- The NPN Open Collector(NPN) is an
interface based on an output circuit with an NPN transistor.
An open collector is the unconnected collector connection of an NPN
transistor, whose emitter is connected to earth and whose collector
is connected to the output.
2. PNP output
The PNP output is an interface based on an output circuit with a
PNP transistor.
3. Push-Pull output(HTL)
High Voltage Transistor Logic functions with a voltage supply in
the range 10 and 30 V DC, with 24 V DC being the most usual.
“Low” is defined as an output of between 0 V and 3 V and “high” as
between VCC and VCC - 3.5 V.
4. TTL RS-422 output
In a transistor-transistor logic (TTL), both the logical status and
the amplification are done by transistors, hence the name.
The TTL output is supplied with either a fixed 5 V voltage or a
variable voltage of between 10 and 32 V. For this the low range is
defined as the ≤ 0.4 V and the high range as ≥ 2.4 V.
